Author - anuj

Faculty Development Program (FDP) on “MasterCAM X9 Multi Axis & Mill – Turn’

A Faculty Development Program (FDP) on “MasterCAM X9 Multi Axis & Mill – Turn’ was organised by Department of Mechanical Engg., ZCOER in association with ‘Onward Technologies, Pune’. This was successfully conducted on 19th & 20th August, 2016.

Machine and G-Code Simulation:

Machine simulation provides you with additional layers of visualization, so that you can zoom in and zoom out at will, to observe everything that will happen during your machining process. You can move the simulation along very quickly in program segments where you are certain that the part, tool, holder fixtures, and peripheral devices (e.g. robots) are in no danger of colliding. When everything is happening in a confined space, you can slow the simulation down to observe these interrelated movements in slow motion or step through them in block fashion

G-code simulation involves a much more extensive modeling process, which is typically done by the software provider.

This program was scheduled for Two Days with:

  • Basics of CAM Programming
  • Use of Simulation in Machining
  • Machine Simulation with G-Code Simulation for Turning
  • Machine Simulation with G-Code Simulation for Milling
  • Machining in Multi axis
  • Machining of Turn- Mill operations were covered
  • Handson training was conducted in MIlling Machine at Skill Development cell.

On receiving feedback from the attendees, the programme was indeed helpful for the faculties to use this software for their further research work and problem solving.

College had fully sponsored this course for the benefit of faculty members.

The resource person for the said training was Mr Rahul Dhage from Onward Technologies, Pune and co-ordinated by Prof. Adewar S. S, Prof Kulkarni O. K. , and Prof Petkar R.

View More images

Celebration of 20th Foundation Day

On behalf of 20th Foundation Day, Zeal Education Society celebrated the colossal event on 3rd August 2016 in
Zeal Narhe Campus. This event was made livelier by unveiling the statue of Shri Chhatrapati Shivaji Maharaj,
Zeal Skill Centre and Zeal Wi-Fi Campus, from the hands of esteemed personalities Hon. Shri. Shriniwasji
Patil, Governor of Sikkim State and Hon.Dr.Wasudeo Gade, Vice Chancellor of SPPU, Pune”.

f10                                   f9

f8                                f7

 

 

 

f1                               f4

 

 

 

 

f5

Condition monitoring techniques used in thermal power plant

Expert lecture conducted on topic “Condition monitoring techniques used in thermal power plant”

An expert lecture on Condition monitoring techniques used in thermal power plant was organized by the department of mechanical engineering shift – I for the student of BE. Mr. Hemant Bari (Senior Manager, MTP Dept, Condition Monitoring Cell, Reliance Infrastructure, Dahanu Thermal Power Station) has successfully conducted Expert Lecture for the final year student for the subject Dynamics of Machinery on topic “Condition monitoring techniques used in thermal power plant”. The students of B.E. (Div. A, Div. B, and Div. C,) were present for this session and the session was very interesting and interactive. Mr. Hemant Bari explores the importance of condition monitoring techniques used in thermal power plant and the various case studies analyzed at Dahanu thermal power station. The session were very useful from exam point of view for the student which gives the knowledge of fundamentals of vibrations and methodology to solve complex problems related to Power Plant usig condition based maintenance.

Topics discussed during program:

  1. Introduction of Dahanu Thermal Power Station.
  2. Condition Monitoring Techniques, Vibration monitoring, Thermography, Lubricant analysis, Acoustic analysis.
  3. Vibration Analysis Technique applied at DTPS to check condition of following critical machines:
  4. Case Studies of PA Fan, Locomotive Engine, BFP

Career Fair

_DSC4933

_DSC4936

Career Fair was conducted in Zeal Polytechnic on 15th June 2016. MSBTE, Mumbai had sponsored this event which was organized in zeal polytechnic.

Site Visit @ Lavasa City

Venue: Lavasa City
Day and Date: Wednesday and 13.07.2016.

Objectives:
1. To generate interest in the subject Building Technology and Materials
2. To introduce different activities carried out on construction site.
3. To introduce different construction materials.
4. To introduce Architectural Planning.

Site Visit Outcomes:
1. Students have got an idea about how the construction sites are getting developed.
2. Students could observe and study different architectural components.
3. Students could learn different geological features along the rout
4. students could learn geotechnical components like Soil types etc.

Visit coordinators: Prof. N. N. Deo, Prof. S.S. Patil, Prof. S.S. Dube.

CATIA V5 Essentials in Mechanical Engineering

A One Day Hands on Training on “CATIA V5 Essentials in Mechanical Engineering”

Organized by Dept. of Mechanical Engg. (Shift-II)

In Association with CORE CADD SOLUTIONS, Pune 22nd July 2016

Submitted by: Prof. Shevale S.S., Assistant Professor, Dept. of Mechanical Engg.

A One Day Hands on Training  on “CATIA V5 Essentials in Mechanical Engineering” Organized by Department of Mechanical Engineering (Shift II) In Association with CORE CADD SOLUTIONS, Pune on 22nd July 2016. Expert, Mr. Sajid Khadas, Engineer-Core Cadd Solutions, who is having real time experience in modeling, worked as onsite deputation Engineer with Global team projects were contributor with significant responsibilities and ownership in designing or engineering the components for Aerospace, Power & water & Automotive industries have been invited as resource person.

The Program was started with formal inauguration addressing the participants by the Prof. Shevale S.S. and HOD of Mechanical Engineering Dr. Kate A.M. Overview of the program and introduction of the Expert from Core Cadd Solutions, Pune was given by Prof. Shevale S.S., Program Coordinator.

Total 35 students were attended CATIA V5 program. The workshop was arranged in two sessions of 2 ½ Hrs each. In the first session was Introduction, Parametric Sketching, Parametric solid modeling, Advance solid modeling tools and Introduction of Surface were discussed. The second session of the workshop was devoted to the practicals on CATIA V5.

The program was interactive and the students are very well technically benefitted from the training. Many real time case studies were discussed and few assignments are given to participants to provide the solutions during the program.

Objective of FDP: At the end of the training the participants will have: Understanding of CATIA VS interface and application of commands for the following modules Sketcher, Part Design, Assembly Design & Drafting.

The event was scheduled to cover the following.

  • Introduction to Part Design
  • Basic Sketch Based Features
  • Basic Dressing-Up Features
  • Part Design Transformations
  • Part Design Modifications
  • Create a new product and add components.
  • Move components within a product by positioning them with assembly
  • Modify an existing product structure.
  • Design new parts in context of the product.
  • Perform interference checking and measurements.
  • Introduction to Generative Shape Design
  • Wireframe Creation

– Introduction to drafting workbench.

End of Training Valedictory was held where feedback from the students was collected and it is observed that the program outlook is satisfactory and the participants expressed that they require similar type of programs in the future.

ADOR CENTER OF EXCELLENCE IN WELDING

INAUGURATION CEREMONY OF “ADOR CENTER OF EXCELLENCE IN WELDING” AT ZEAL SKILL CENTER NARHE PUNE

The Government’s “Make in India” initiative has attracted large amounts of foreign investments to the country with a specific focus on manufacturing. Welding is a very vast Engineering subject which covers the creation of a simple fabrication structure like gate, from underwater welding to spacecraft components and the practice of welding is basic to building infrastructure in the country. It has different levels of complexities depending on whether it is used in power plants, railway coaches, aircrafts or spacecraft. This offers an opportunity for the engineers, and the welders, not only to learn about the welding skills, but also learn about the process of welding, and how it can be managed and improved, and new fabrication practices for complex materials.

There is lot of theory, research and development, career prospects and production related practices, which the engineers can develop. By Considering all these aspects of Welding Zeal Skill Center of ZCOER had developed a well-equipped Lab.It Includes Various facilities like Welding Simulator, Live demonstration Center, Shield  Metal Arc Welding,TIG Welding,MIG Welding, Multipurpose Machine, Baking Oven etc. This lab is developed jointly in association with ADOR Welding Limited, Mumbai and Skill Center, Zeal College of Engineering and Research.Prof.Aashish Gandigude (In charge of Excellence Lab, ZCOER) introduced eminent guests and briefed about the idea behind Ador center of Excellence in welding.

Dr.S.G.Dambhare, HOD, Mechanical Engineering, introduced eminent guests about other facilities at the skill center like Automobile Excellence Lab, Machining Excellence Lab, and Power Plant Lab etc.

The Lab was inaugurated on 18th July 2016 by Mr. Deep A. Lalvani (Director Ador Welding Ltd, Head CSR Committee Ador Welding Ltd, Mumbai).On this Occasion Mr.Ramankumar (Chairman Ador Welding Academy Pvt. Ltd, Pune) guided the students regarding career prospectus and huge opportunities in the field of Welding. Mr. Lalvani congratulated Zeal Education Society for providing such unique facility for engineering students.Mr.Sanjay Gandhi, Corporate Trainer from ASPIRE praised Zeal Education Society for developing skills in the field of Automobile Excellence, Machining Excellence along with Welding. Dr.S.G.Dambhare, HOD, Mechanical Engineering, gave the vote of thanks.

Prof.Jayesh Katkar, Executive Director, Zeal Education Society, Dr.Arun Gaikwad, Principal, Zeal College of Engineering and Research, Dr.Sanjay Deokar, Director Admissions and Placement were present for the Inaugural function. Prof. Dr. C.L.Prabhune, Prof. Dr.Subash Kamal, Prof.B.D.Aldar Second shift HoD Mechanical,Prof.A.R.Suryavanshi, Prof. J.Shaikh ME-CADME coordinator, Prof.V.H.Barge TPO, Prof.P.P.Ritapure -ME Design coordinator and staff of Mechanical Engineering were present on this occasion.

GO-KART EVENT

Recently team “ACCELERONS” participated in “Indian super carting Series 2016” organized by “Mahankal institute of Technology”, Ujjain, M.P.  Accelerons is a group of 15 students from SE.TE, BE along with faculty Advisor Prof. A.V. Karande. Event was scheduled on 8th -10th July 2016 at MIT,Ujjain. Based on our performance at International go-kart championship, organized by LPU, Punjab where we grabbed pole position in Endurance, we were directly allowed for Dynamic Round. Technical inspection was performed to check whether vehicle meets defined rules and safety measures for Driver. Team Received special compliment from FMSCI judges regarding our safety measures in vehicle. We successfully cleared Technical inspection in first attempt. Dynamic round consists of acceleration Test, Brake test and figure of eight etc. In acceleration test we took 10 sec to cover 60 m distance but based on our engine which is only 3.5 HP, we were considered as best among all the teams and hence we got top rank in that category. Brake test was followed by acceleration test where our vehicle took 8 m stopping distance. Lastly vehicle completed figure of Eight in 37 seconds. In Dynamic round, earlier it was scheduled to complete 3 laps with 2 liter fuel but due to continuous rain there was change in the rule. Now the vehicle has to run for one lap and winner for this was declared based on minimum time. Our vehicle completed track in one minute 40 second.

   Our team won “Best Acceleration Award” and also we are ranked All India 8th among 70 teams. We heartily thankful to Dr. S. G. Dambhhare sir,HOD(Mechanical Engg.) for allowing us to participation in event and extending workshop facilities for 24×7 for manufacturing and testing of vehicle. Also we thank Dr. A.N. Gaikwad, Principal, ZCOER for his guidance and support. We are grateful to Prof. Jayesh Katkar,Ex. Director, ZES for their continuous motivation and inspiration.

  zeal2zeal4zeal5zeal3